Product Guides
Tap your product below to see the full step-by-step guide, so you can set it up in minutes and discover every feature it has to offer.
Still stuck or something not working as expected? Reach us on +91 63609 82961 or support@tintloop.in, we're happy to help 😊
-
Charge the camera 🔋
Connect the USB cable and charge the camera fully before the first use. This usually takes 30–40 minutes.
-
Power on ⚡
Press and hold the Power button for 2–3 seconds.
-
Take photos 📸
Select Photo Mode, frame your subject on the screen and press the Shutter button.
Use the Previous / Next buttons to apply fun filters.
An SD card is not included. Insert one if you want to save more photos.
-
Print photos 🖨️
Turn Print Mode ON and take a photo — the picture prints automatically.
- Make sure the printing paper is properly inserted in the front compartment.
- If the roll sits loose, roll it up tightly and insert it again.
- Load the thermal paper with the printing side (the smoother surface) facing the correct direction.
Use only the recommended thermal printing paper for your camera.
-
Switch between cameras 🤳
Press the front camera button to switch between the front and rear cameras. On some units the Previous / Next buttons also switch cameras.
-
Adjust settings ⚙️
Open Settings / Menu to adjust:
- Photo resolution — how refined your images look.
- Print density — from a light print to a deep black print.
- Print type
- Volume
Have fun capturing and printing your memories ❤️ You can also play games and listen to music on this one 🎮🎵
-
Charge both units 🔋
Connect the USB charging cable to the charging port and charge each walkie talkie fully before use.
-
Power on / off 🔴
Toggle the Power switch on the left side to turn the walkie talkie ON or OFF.
-
Talk and listen 🎙️
- Turn ON both walkie talkies.
- Tap the call icon, then dial by pressing the right side button.
- On the other walkie talkie, press the right side button to accept the call.
- Press and hold the right side button while you speak.
- Release the button when you finish speaking so you can listen.
- Press the top button to end the call or go back.
Hold the right button to talk 🎙️, release it to listen 👂. Both users cannot speak at the same time.
-
Send a voice message 🎤
Open Message / Chat, select the other walkie talkie and follow the on-screen instructions to record and send a voice message.
-
Send a text message 💬
Open Chat / Messages, select the other walkie talkie and type your message using the on-screen keyboard, then tap Send. You can also send photos and emojis.
-
Take a photo 📸
Open Camera, point it at what you want to capture and press the Shutter button on the right side. Photos are saved automatically.
This set has a front camera only.
-
Send a photo 🖼️
Open Gallery, select the photo you want to share, tap Send and choose the other walkie talkie.
-
Delete a photo 🗑️
Open Gallery and select the photo. Long press the right side button until the Delete option appears, then choose Delete.
Have fun talking, taking photos and sharing messages 🎉
-
Power on 💡
Connect the lamp to a suitable power source and press the Power button to switch it ON or OFF.
-
Use it as a night light 🌙
Switch the lamp ON to enjoy its soft, cozy glow.
-
Use the projector ⭐
- Remove the white outer covering.
- Remove the top projector cover.
- Point the projector towards a wall or ceiling.
- Switch ON the projector to enjoy the projected patterns.
-
Change the projector film 🎞️
Long film
- Take out the white outer covering and the top cover.
- Remove the existing long film from the film slot.
- Insert the new film carefully into the slot.
- Make sure it is positioned correctly before switching the projector ON.
Circular film
- Remove the top projector cover.
- Take out the existing circular film.
- Place the new circular film in the film holder.
- Put the cover back securely and switch the projector ON.
-
Carousel feature 🐰
Switch ON the rotation function to make the bunny carousel rotate.
Care & safety ⚠️
- Handle the films and covers gently.
- Keep the lamp away from water.
- Do not cover the lamp while it is ON.
- Allow the lamp to cool before changing films.
Change the film, change the mood, and enjoy your magical projector ✨
-
Remove the protective film 🛡️
Before using the board, carefully peel off the transparent protective film from both sides of the acrylic panel for a clear, shiny surface.
-
Power on 💡
Connect the USB cable to the writing board and to a suitable power source.
-
Write and draw ✍️
Use the included neon / LED marker pens to write or draw on the acrylic surface.
-
Clean and reuse 🧽
When you are ready for a new drawing, gently wipe the surface with a soft, dry or slightly damp cloth.
Care tips ⚠️
- Remove the protective film before the first use.
- Use only suitable markers on the acrylic surface.
- Clean gently with a soft cloth.
- Keep the USB connection away from water.
Write. Glow. Wipe. Repeat 🎨
-
Insert the batteries 🔋
- Open the battery compartment on the back of the teddy.
- Insert the batteries according to the + and − markings inside the compartment.
- Move the ON / OFF switch to the ON position.
- Close the battery cover securely before use.
-
Start the breathing feature 🌙
Press the button marked with the music sign on the teddy's feet to activate the gentle breathing motion. The tummy slowly rises and falls to create a calming effect.
-
Lights and sounds 🎵
Press the button to adjust the soothing sounds and soft lights.
-
Power off 🔕
Switch the teddy OFF when it is not in use to save battery life.
Cuddle, relax, and drift into a peaceful sleep 💤
-
Connect the lamp 🔌
Connect the USB cable to a suitable USB power adapter and switch the lamp ON.
Avoid using a power bank.
-
Turn on 💡
Use the remote or the control buttons to switch the lamp ON / OFF and control the available functions.
-
Projector mode 🌌
Point the astronaut projector towards a wall or ceiling. Adjust the astronaut's head and position to get the best projection.
-
Change light effects 🌈
Use the remote to change the colours, brightness and lighting effects.
-
Set the timer ⏰
Use the Timer button on the remote to switch the lamp OFF automatically.
Care & safety ⚠️
- Use only a suitable USB power adapter.
- Keep away from water and moisture.
- Handle the astronaut's movable parts gently.
- Do not stare directly into the LED light.
Create your own galaxy and light up your space ✨